SECTION XV · Capitolo 72
Iron and steel
Nomenclatura e aliquote 2026 dalla tariffa consolidata BT2026. FONTE
Note di capitolo (63)
Notes
1. In this Chapter and, in the case of Notes (d), (e) and (f) throughout the Nomenclature, the following expressions have the meanings hereby assigned to them:
(a) Pig iron
Iron-carbon alloys not usefully malleable, containing more than 2% by weight of carbon and which may contain by weight one or more other elements within the following limits:
(b) Spiegeleisen
Iron-carbon alloys containing by weight more than 6% but not more than 30% of manganese and otherwise conforming to the specification at (a) above.
(c) Ferro-alloys
Alloys in pigs, blocks, lumps or similar primary forms, in forms obtained by continuous casting and also in granular or powder forms, whether or not agglomerated, commonly used as an additive in the manufacture of other alloys or as de-oxidants, de-sulphurising agents or for similar uses in ferrous metallurgy and generally not usefully malleable, containing by weight 4% or more of the element iron and one or more of the following:
(d) Steel
Ferrous materials other than those of heading 72.03 which (with the exception of certain types produced in the form of castings) are usefully malleable and which contain by weight 2% or less of carbon. However, chromium steels may contain higher proportions of carbon.
(e) Stainless steel
Alloy steels containing, by weight, 1.2% or less of carbon and 10.5% or more of chromium, with or without other elements.
(f) Other alloy steel
Steels not complying with the definition of stainless steel and containing by weight one or more of the following elements in the proportion shown:
(g) Remelting scrap ingots of iron or steel
Products roughly cast in the form of ingots without feeder-heads or hot tops, or of pigs, having obvious surface faults and not complying with the chemical composition of pig iron, spiegeleisen or ferro-alloys.
(h) Granules
Products of which less than 90% by weight passes through a sieve with a mesh aperture of 1 mm and of which 90% or more by weight passes through a sieve with a mesh aperture of 5 mm.
(ij) Semi-finished products
Continuous cast products of solid section, whether or not subjected to primary hot-rolling; and
Other products of solid section, which have not been further worked than subjected to primary hot-rolling or roughly shaped by forging, including blanks for angles, shapes or sections.
These products are not presented in coils.
(k) Flat-rolled products
Rolled products of solid rectangular (other than square) cross-section, which do not conform to the definition at (ij) above in the form of:
Flat-rolled products include those with patterns in relief derived directly from rolling (for example, grooves, ribs, chequers, tears, buttons, lozenges) and those which have been perforated, corrugated or polished, provided that they do not thereby assume the character of articles or products of other headings.
Flat-rolled products of a shape other than rectangular or square, of any size, are to be classified as products of a width of 600 mm or more, provided that they do not assume the character of articles or products of other headings.
(l) Bars and rods, hot-rolled, in irregularly wound coils
Hot-rolled products in irregularly wound coils, which have a solid cross-section in the shape of circles, segments of circles, ovals, rectangles (including squares), triangles or other convex polygons (including “flattened circles” and “modified rectangles”, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). These products may have indentations, ribs, grooves or other deformations produced during the rolling process (reinforcing bars and rods).
(m) Other bars and rods
Products which do not conform to any of the definitions at (ij), (k) or (l) above or to the definition of wire, which have a uniform solid cross-section along their whole length in the shape of circles, segments of circles, ovals, rectangles (including squares), triangles or other convex polygons (including “flattened circles” and “modified rectangles”, of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). These products may:
(n) Angles, shapes and sections
Products having a uniform solid cross-section along their whole length which do not conform to any of the definitions at (ij), (k), (l) or (m) above or to the definition of wire.
Chapter 72 does not include products of heading 73.01 or 73.02.
(o) Wire
Cold-formed products in coils, of any uniform solid cross-section along their whole length, which do not conform to the definition of flat-rolled products.
(p) Hollow drill bars and rods
Hollow bars and rods of any cross-section, suitable for drills, of which the greatest external dimension of the cross-section exceeds 15 mm but does not exceed 52 mm, and of which the greatest internal dimension does not exceed one half of the greatest external dimension. Hollow bars and rods of iron or steel not conforming to this definition are to be classified in heading 73.04.
2. Ferrous metals clad with another ferrous metal are to be classified as products of the ferrous metal predominating by weight.
3. Iron or steel products obtained by electrolytic deposition, by pressure casting or by sintering are to be classified, according to their form, their composition and their appearance, in the headings of this Chapter appropriate to similar hot-rolled products.
Subheading Notes.
1. In this Chapter the following expressions have the meanings hereby assigned to them:
(a) Alloy pig iron
Pig iron containing, by weight, one or more of the following elements in the specified proportions:
(b) Non-alloy free-cutting steel
Non-alloy steel containing, by weight, one or more of the following elements in the specified proportions:
(c) Silicon-electrical steel
Alloy steels containing by weight at least 0.6% but not more than 6% of silicon and not more than 0.08% of carbon. They may also contain by weight not more than 1% of aluminium but no other element in a proportion that would give the steel the characteristics of another alloy steel.
(d) High speed steel
Alloy steels containing, with or without other elements, at least two of the three elements molybdenum, tungsten and vanadium with a combined content by weight of 7% or more, 0.6% or more of carbon and 3 to 6% of chromium.
(e) Silico-manganese steel
Alloy steels containing by weight:
2. For the classification of ferro-alloys in the subheadings of heading 72.02 the following rule should be observed:
A ferro-alloy is considered as binary and classified under the relevant subheading (if it exists) if only one of the alloy elements exceeds the minimum percentage laid down in Chapter Note 1 (c); by analogy, it is considered respectively as ternary or quaternary if two or three alloy elements exceed the minimum percentage.
For the application of this rule the unspecified “other elements” referred to in Chapter Note 1 (c) must each exceed 10% by weight.
SUB-CHAPTER I
PRIMARY MATERIALS; PRODUCTS IN GRANULAR OR POWDER FORM
SUB-CHAPTER II
IRON AND NON-ALLOY STEEL
SUB-CHAPTER III
STAINLESS STEEL
SUB-CHAPTER IV
OTHER ALLOY STEEL; HOLLOW DRILL BARS AND RODS, OF ALLOY OR NON- ALLOY STEEL
(SEN): Tham khảo Chú giải bổ sung (SEN) của Danh mục Thuế quan hài hòa ASEAN (AHTN) 2022
| Codice SA | Descrizione | Unità | Dazio all'importazione ordinario | MFN | VAT |
|---|---|---|---|---|---|
| - not more than 10% of chromium | |||||
| - not more than 6% of manganese | |||||
| - not more than 3% of phosphorus | |||||
| - not more than 8% of silicon | |||||
| - a total of not more than 10% of other elements. | |||||
| - more than 10% of chromium | |||||
| - more than 30% of manganese | |||||
| - more than 3% of phosphorus | |||||
| - more than 8% of silicon | |||||
| - a total of more than 10% of other elements, excluding carbon, subject to a maximum content of 10% in the case of copper. | |||||
| - 0.3% or more of aluminium | |||||
| - 0.0008% or more of boron | |||||
| - 0.3% or more of chromium | |||||
| - 0.3% or more of cobalt | |||||
| - 0.4% or more of copper | |||||
| - 0.4% or more of lead | |||||
| - 1.65% or more of manganese | |||||
| - 0.08% or more of molybdenum | |||||
| - 0.3% or more of nickel | |||||
| - 0.06% or more of niobium | |||||
| - 0.6% or more of silicon | |||||
| - 0.05% or more of titanium | |||||
| - 0.3% or more of tungsten (wolfram) | |||||
| - 0.1% or more of vanadium | |||||
| - 0.05% or more of zirconium | |||||
| - 0.1% or more of other elements (except sulphur, phosphorus, carbon and nitrogen), taken separately. | |||||
| - coils of successively superimposed layers, or | |||||
| - straight lengths, which if of a thickness less than 4.75 mm are of a width measuring at least ten times the thickness or if of a thickness of 4.75 mm or more are of a width which exceeds 150 mm and measures at least twice the thickness. | |||||
| - have indentations, ribs, grooves or other deformations produced during the rolling process (reinforcing bars and rods); | |||||
| - be twisted after rolling. | |||||
| - more than 0.2% of chromium | |||||
| - more than 0.3% of copper | |||||
| - more than 0.3% of nickel | |||||
| - more than 0.1% of any of the following elements: aluminium, molybdenum, titanium, tungsten (wolfram), vanadium. | |||||
| - 0.08% or more of sulphur | |||||
| - 0.1% or more of lead | |||||
| - more than 0.05% of selenium | |||||
| - more than 0.01% of tellurium | |||||
| - more than 0.05% of bismuth. | |||||
| - not more than 0.7% of carbon, | |||||
| - 0.5% or more but not more than 1.9% of manganese, and | |||||
| - 0.6% or more but not more than 2.3% of silicon, but no other element in a proportion that would give the steel the characteristics of another alloy steel. | |||||
| 7201 | Pig iron and, spiegeleisen in pigs, blocks or other primary forms | ||||
| 7201.10.00 | - Non-alloy pig iron containing by weight 0.5% or less of phosphorus | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7201.20.00 | - Non-alloy pig iron containing by weight more than 0.5% of phosphorus | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7201.50.00 | - Alloy pig iron; spiegeleisen | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7202 | Ferro-alloys | ||||
| - Ferro-manganese: | |||||
| 7202.11.00 | - - Containing by weight more than 2% of carbon | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7202.19.00 | - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - Ferro-silicon: | |||||
| 7202.21.00 | - - Containing by weight more than 55% of silicon | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7202.29.00 | - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7202.30.00 | - Ferro-silico-manganese | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - Ferro-chromium: | |||||
| 7202.41.00 | - - Containing by weight more than 4% of carbon | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7202.49.00 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7202.50.00 | - Ferro-silico-chromium | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7202.60.00 | - Ferro-nickel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7202.70.00 | - Ferro-molybdenum | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7202.80.00 | - Ferro-tungsten and ferro-silico-tungsten | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Other: | |||||
| 7202.91.00 | - - Ferro-titanium and ferro-silico-titanium | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7202.92.00 | - - Ferro-vanadium | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7202.93.00 | - - Ferro-niobium | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7202.99.00 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7203 | Ferrous products obtained by direct reduction of iron ore and other spongy ferrous products, in lumps, pellets or similar forms; iron having a minimum purity by weight of 99.94%, in lumps, pellets or similar forms | ||||
| 7203.10.00 | - Ferrous products obtained by direct reduction of iron ore | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7203.90.00 | - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7204 | Ferrous waste and scrap; remelting scrap ingots of iron or steel | ||||
| 7204.10.00 | - Waste and scrap of cast iron | kg | 4,5% | 3% | 10 / 8 (più aliquote) |
| - Waste and scrap of alloy steel: | |||||
| 7204.21.00 | - - Of stainless steel | kg | 5% | 0% | 8 / 10 (più aliquote) |
| 7204.29.00 | - - Other | kg | 5% | 0% | 8 / 10 (più aliquote) |
| 7204.30.00 | - Waste and scrap of tinned iron or steel | kg | 5% | 0% | 8 / 10 (più aliquote) |
| - Other waste and scrap: | |||||
| 7204.41.00 | - - Turnings, shavings, chips, milling waste, sawdust, filings, trimmings and stampings, whether or not in bundles | kg | 4,5% | 3% | 8 / 10 (più aliquote) |
| 7204.49.00 | - - Other | kg | 5% | 0% | 8 / 10 (più aliquote) |
| 7204.50.00 | - Remelting scrap ingots | kg | 4,5% | 3% | 8 / 10 (più aliquote) |
| 7205 | Granules and powders, of pig iron, spiegeleisen, iron or steel | ||||
| 7205.10.00 | - Granules | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Powders: | |||||
| 7205.21.00 | - - Of alloy steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7205.29.00 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7206 | Iron and non-alloy steel in ingots or other primary forms (excluding iron of heading 72.03) | ||||
| 7206.10 | - Ingots: | ||||
| 7206.10.10 | - - Containing by weight more than 0.6% of carbon | kg | 1,5% | 1% | 10 / 8 (più aliquote) |
| 7206.10.90 | - - Other | kg | 1,5% | 1% | 10 / 8 (più aliquote) |
| 7206.90.00 | - Other | kg | 1,5% | 1% | 10 / 8 (più aliquote) |
| 7207 | Semi-finished products of iron or non-alloy steel | ||||
| - Containing by weight less than 0.25% of carbon: | |||||
| 7207.11.00 | - - Of rectangular (including square) cross-section, the width measuring less than twice the thickness | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7207.12 | - - Other, of rectangular (other than square) cross-section: | ||||
| 7207.12.10 | - - - Slabs | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7207.12.90 | - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7207.19.00 | - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7207.20 | - Containing by weight 0.25% or more of carbon: | ||||
| - - Containing by weight less than 0.6% of carbon: | |||||
| 7207.20.10 | - - - Slabs | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7207.20.21 | - - - - Blocks roughly shaped by forging; sheet bars | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7207.20.29 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7207.20.91 | - - - Slabs | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7207.20.92 | - - - - Blocks roughly shaped by forging; sheet bars | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7207.20.99 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7208 | Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, hot-rolled, not clad, plated or coated | ||||
| 7208.10.00 | - In coils, not further worked than hot-rolled, with patterns in relief | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Other, in coils, not further worked than hot-rolled, pickled: | |||||
| 7208.25.00 | - - Of a thickness of 4.75 mm or more | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.26.00 | - - Of a thickness of 3 mm or more but less than 4.75 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.27 | - - Of a thickness of less than 3 mm: | ||||
| - - - Of a thickness of less than 2 mm: | |||||
| 7208.27.11 | - - - - Containing by weight 0.6% or more of carbon | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.27.19 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7208.27.91 | - - - - Containing by weight 0.6% or more of carbon | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.27.99 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Other, in coils, not further worked than hot-rolled: | |||||
| 7208.36.00 | - - Of a thickness exceeding 10 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.37.00 | - - Of a thickness of 4.75 mm or more but not exceeding 10 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.38.00 | - - Of a thickness of 3 mm or more but less than 4.75 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.39 | - - Of a thickness of less than 3 mm: | ||||
| 7208.39.10 | - - - Containing by weight less than 0.6% of carbon and of a thickness of 0.17 mm or less | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.39.20 | - - - Containing by weight less than 0.6% of carbon and of a thickness more than 0.17 mm but not exceeding 1.5 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.39.30 | - - - Containing by weight 0.6% or more of carbon and of a thickness not exceeding 1.5 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.39.40 | - - - Of a thickness more than 2 mm, maximum tensile strength of 550 Mpa and of a width not exceeding 1,250 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.39.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.40.00 | - Not in coils, not further worked than hot-rolled, with patterns in relief | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Other, not in coils, not further worked than hot-rolled: | |||||
| 7208.51.00 | - - Of a thickness exceeding 10 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.52.00 | - - Of a thickness of 4.75 mm or more but not exceeding 10 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.53.00 | - - Of a thickness of 3 mm or more but less than 4.75 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.54 | - - Of a thickness of less than 3 mm: | ||||
| 7208.54.10 | - - - Containing by weight less than 0.6% of carbon and of a thickness of 0.17 mm or less | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.54.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.90 | - Other: | ||||
| 7208.90.10 | - - Corrugated | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.90.20 | - - Other, containing by weight less than 0.6% of carbon and of a thickness of 0.17 mm or less | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7208.90.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7209 | Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, cold-rolled (cold-reduced), not clad, plated or coated | ||||
| - In coils, not further worked than cold-rolled (cold-reduced): | |||||
| 7209.15.00 | - - Of a thickness of 3 mm or more | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.16 | - - Of a thickness exceeding 1 mm but less than 3 mm: | ||||
| 7209.16.10 | - - - Of a width not exceeding 1,250 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.16.90 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.17 | - - Of a thickness of 0.5 mm or more but not exceeding 1 mm: | ||||
| 7209.17.10 | - - - Of a width not exceeding 1,250 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.17.90 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.18 | - - Of a thickness of less than 0.5 mm: | ||||
| 7209.18.10 | - - - Tin-mill blackplate | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7209.18.91 | - - - - Containing by weight less than 0.6% of carbon and of a thickness of 0.17 mm or less | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.18.99 | - - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| - Not in coils, not further worked than cold-rolled (cold-reduced): | |||||
| 7209.25.00 | - - Of a thickness of 3 mm or more | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.26 | - - Of a thickness exceeding 1 mm but less than 3 mm: | ||||
| 7209.26.10 | - - - Of a width not exceeding 1,250 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.26.90 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.27 | - - Of a thickness of 0.5 mm or more but not exceeding 1 mm: | ||||
| 7209.27.10 | - - - Of a width not exceeding 1,250 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.27.90 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.28 | - - Of a thickness of less than 0.5 mm: | ||||
| 7209.28.10 | - - - Containing by weight less than 0.6% of carbon and of a thickness of 0.17 mm or less | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.28.90 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.90 | - Other: | ||||
| 7209.90.10 | - - Corrugated | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7209.90.90 | - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7210 | Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, clad, plated or coated | ||||
| - Plated or coated with tin: | |||||
| 7210.11 | - - Of a thickness of 0.5 mm or more: | ||||
| 7210.11.10 | - - - Containing by weight 0.6% or more of carbon | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.11.90 | - - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.12 | - - Of a thickness of less than 0.5 mm: | ||||
| 7210.12.10 | - - - Containing by weight 0.6% or more of carbon | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.12.90 | - - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.20 | - Plated or coated with lead, including terne-plate: | ||||
| 7210.20.10 | - - Containing by weight less than 0.6% of carbon and of a thickness of 1.5 mm or less | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7210.20.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7210.30 | - Electrolytically plated or coated with zinc: | ||||
| - - Containing by weight less than 0.6% of carbon: | |||||
| 7210.30.11 | - - - Of a thickness not exceeding 1.2 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.30.12 | - - - Of a thickness exceeding 1.2 mm but not exceeding 1.5 mm | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.30.19 | - - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7210.30.91 | - - - Of a thickness not exceeding 1.2 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.30.99 | - - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - Otherwise plated or coated with zinc: | |||||
| 7210.41 | - - Corrugated: | ||||
| - - - Containing by weight less than 0.6% of carbon: | |||||
| 7210.41.11 | - - - - Of a thickness not exceeding 1.2 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7210.41.12 | - - - - Of a thickness exceeding 1.2 mm but not exceeding 1.5 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.41.19 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7210.41.91 | - - - - Of a thickness not exceeding 1.2 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7210.41.99 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.49 | - - Other: | ||||
| - - - Containing by weight less than 0.6% of carbon: | |||||
| 7210.49.11 | - - - - Coated with zinc by the iron-zinc alloyed coating method, containing by weight less than 0.04% of carbon and of a thickness not exceeding 1.2 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7210.49.14 | - - - - Plated or coated with zinc-aluminium-magnesium alloys, of a thickness not exceeding 1.2 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7210.49.15 | - - - - Plated or coated with zinc-aluminium-magnesium alloys, of a thickness exceeding 1.2 mm but not exceeding 1.5 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.49.16 | - - - - Plated or coated with zinc-aluminium-magnesium alloys, of a thickness exceeding 1.5 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.49.17 | - - - - Other, of a thickness not exceeding 1.2 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7210.49.18 | - - - - Other, of a thickness exceeding 1.2 mm but not exceeding 1.5 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.49.19 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7210.49.91 | - - - - Of a thickness not exceeding 1.2 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7210.49.99 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.50.00 | - Plated or coated with chromium oxides or with chromium and chromium oxides | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - Plated or coated with aluminium: | |||||
| 7210.61 | - - Plated or coated with aluminium-zinc alloys: | ||||
| - - - Containing by weight less than 0.6% of carbon: | |||||
| 7210.61.11 | - - - - Of a thickness not exceeding 1.2 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7210.61.12 | - - - - Of a thickness exceeding 1.2 mm but not exceeding 1.5 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.61.19 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7210.61.91 | - - - - Of a thickness not exceeding 1.2 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7210.61.92 | - - - - Other, corrugated | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.61.99 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.69 | - - Other: | ||||
| - - - Containing by weight less than 0.6% of carbon: | |||||
| 7210.69.11 | - - - - Of a thickness not exceeding 1.2 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7210.69.19 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7210.69.91 | - - - - Of a thickness not exceeding 1.2 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7210.69.99 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7210.70 | - Painted, varnished or coated with plastics: | ||||
| - - Containing by weight less than 0.6% of carbon and of a thickness of 1.5 mm or less: | |||||
| 7210.70.12 | - - - Painted after coating with zinc | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.70.13 | - - - Painted after coating with aluminium-zinc alloys | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.70.19 | - - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - - Other, containing by weight less than 0.6% of carbon: | |||||
| 7210.70.21 | - - - Painted | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.70.29 | - - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7210.70.91 | - - - Painted | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.70.99 | - - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.90 | - Other: | ||||
| 7210.90.10 | - - Containing by weight less than 0.6% of carbon and of a thickness of 1.5 mm or less | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7210.90.90 | - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7211 | Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, not clad, plated or coated | ||||
| - Not further worked than hot-rolled: | |||||
| 7211.13 | - - Rolled on four faces or in a closed box pass, of a width exceeding 150 mm and a thickness of not less than 4 mm, not in coils and without patterns in relief: | ||||
| - - - Containing by weight less than 0.6% of carbon: | |||||
| 7211.13.12 | - - - - Corrugated | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.13.13 | - - - - Hoop and strip | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.13.14 | - - - - Universal plates | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.13.19 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7211.13.92 | - - - - Hoop and strip | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.13.93 | - - - - Universal plates | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.13.99 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.14 | - - Other, of a thickness of 4.75 mm or more: | ||||
| - - - Containing by weight less than 0.6% of carbon: | |||||
| 7211.14.14 | - - - - Corrugated | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.14.15 | - - - - Coils for re-rolling | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.14.16 | - - - - Hoop and strip | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.14.17 | - - - - Universal plates | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.14.19 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7211.14.94 | - - - - Hoop and strip | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.14.95 | - - - - Universal plates | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.14.99 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7211.19 | - - Other: | ||||
| - - - Containing by weight less than 0.6% of carbon: | |||||
| 7211.19.13 | - - - - Hoop and strip; universal plates | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7211.19.14 | - - - - Corrugated | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.19.19 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7211.19.91 | - - - - Hoop and strip; universal plates | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7211.19.99 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Not further worked than cold-rolled (cold-reduced): | |||||
| 7211.23 | - - Containing by weight less than 0.25% of carbon: | ||||
| 7211.23.10 | - - - Corrugated | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.23.20 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.23.30 | - - - Other, of a thickness of 0.17 mm or less | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.23.90 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.29 | - - Other: | ||||
| 7211.29.10 | - - - Corrugated | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.29.20 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.29.30 | - - - Other, of a thickness of 0.17 mm or less | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.29.90 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.90 | - Other: | ||||
| - - Containing by weight less than 0.6% of carbon: | |||||
| 7211.90.11 | - - - Hoop and strip, of a width not exceeding 25 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.90.12 | - - - Hoop and strip, of a width exceeding 400 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.90.13 | - - - Corrugated | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.90.14 | - - - Other, of a thickness of 0.17 mm or less | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.90.19 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7211.90.91 | - - - Of a thickness of 0.17 mm or less | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7211.90.99 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7212 | Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, clad, plated or coated | ||||
| 7212.10 | - Plated or coated with tin: | ||||
| - - Containing by weight less than 0.6% of carbon: | |||||
| 7212.10.11 | - - - Hoop and strip, of a width not exceeding 25 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7212.10.14 | - - - Hoop and strip, of a width exceeding 400 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7212.10.19 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7212.10.94 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7212.10.99 | - - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7212.20 | - Electrolytically plated or coated with zinc: | ||||
| 7212.20.10 | - - Hoop and strip, of a width not exceeding 400 mm | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7212.20.20 | - - Other, containing by weight less than 0.6% of carbon and of a thickness of 1.5 mm or less | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7212.20.90 | - - Other | kg | 10,5% | 7% | 10 / 8 (più aliquote) |
| 7212.30 | - Otherwise plated or coated with zinc: | ||||
| - - Containing by weight less than 0.6% of carbon: | |||||
| 7212.30.11 | - - - Hoop and strip, of a width not exceeding 25 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.30.12 | - - - Hoop and strip, of a width exceeding 25 mm and not exceeding 400 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.30.13 | - - - Other, of a thickness of 1.5 mm or less | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.30.14 | - - - Other, coated with zinc by the iron-zinc alloy coating method, containing by weight less than 0.04% of carbon | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.30.19 | - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.30.90 | - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.40 | - Painted, varnished or coated with plastics: | ||||
| - - Containing by weight less than 0.6% of carbon: | |||||
| 7212.40.11 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.40.12 | - - - Other hoop and strip | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.40.13 | - - - Other, painted after coating with zinc | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.40.14 | - - - Other, painted after coating with aluminium-zinc alloys | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.40.19 | - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7212.40.91 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.40.99 | - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.50 | - Otherwise plated or coated: | ||||
| - - Plated or coated with chromium oxides or with chromium and chromium oxides: | |||||
| 7212.50.14 | - - - Hoop and strip, of a width exceeding 25 mm; universal plates | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.50.19 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - Plated or coated with aluminium-zinc alloys: | |||||
| 7212.50.23 | - - - Hoop and strip, of a width not exceeding 25 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.50.24 | - - - Other hoop and strip; universal plates | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7212.50.29 | - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7212.50.93 | - - - Hoop and strip, of a width not exceeding 25 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.50.94 | - - - Other hoop and strip; universal plates | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.50.99 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.60 | - Clad: | ||||
| - - Containing by weight less than 0.6% of carbon: | |||||
| 7212.60.11 | - - - Hoop and strip | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.60.12 | - - - Other, of a thickness of 1.5 mm or less | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.60.19 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7212.60.91 | - - - Hoop and strip | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7212.60.99 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7213 | Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel | ||||
| 7213.10 | - Containing indentations, ribs, grooves or other deformations produced during the rolling process: | ||||
| 7213.10.10 | - - Of circular cross-section measuring not exceeding 50 mm in diameter | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7213.10.90 | - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7213.20.00 | - Other, of free-cutting steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Other: | |||||
| 7213.91 | - - Of circular cross-section measuring less than 14 mm in diameter: | ||||
| 7213.91.10 | - - - Of a kind used for producing soldering sticks | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7213.91.20 | - - - Of a kind used for concrete reinforcement (rebars) | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7213.91.30 | - - - Other, containing by weight 0.6% or more of carbon, not more than 0.03% of phosphorus and not more than 0.035% of sulphur | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7213.91.90 | - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7213.99 | - - Other: | ||||
| 7213.99.10 | - - - Of a kind used for producing soldering sticks | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7213.99.20 | - - - Of a kind used for concrete reinforcement (rebars) | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7213.99.90 | - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7214 | Other bars and rods of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but including those twisted after rolling | ||||
| 7214.10 | - Forged: | ||||
| - - Containing by weight less than 0.6% of carbon: | |||||
| 7214.10.11 | - - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.10.19 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7214.10.21 | - - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.10.29 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.20 | - Containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling: | ||||
| - - Containing by weight less than 0.6% of carbon: | |||||
| - - - Of circular cross-section: | |||||
| 7214.20.31 | - - - - Of a kind used for concrete reinforcement (rebars) | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7214.20.39 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7214.20.41 | - - - - Of a kind used for concrete reinforcement (rebars) | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7214.20.49 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| - - - Of circular cross-section: | |||||
| 7214.20.51 | - - - - Of a kind used for concrete reinforcement (rebars) | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7214.20.59 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7214.20.61 | - - - - Of a kind used for concrete reinforcement (rebars) | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7214.20.69 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7214.30 | - Other, of free-cutting steel: | ||||
| 7214.30.10 | - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.30.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Other: | |||||
| 7214.91 | - - Of rectangular (other than square) cross-section: | ||||
| - - - Containing by weight less than 0.6% of carbon: | |||||
| 7214.91.11 | - - - - Containing by weight 0.38% or more of carbon and less than 1.15% of manganese | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.91.12 | - - - - Containing by weight 0.17% or more but not more than 0.46% of carbon and 1.2% or more but less than 1.65% of manganese | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.91.19 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.91.20 | - - - Containing by weight 0.6% or more of carbon | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.99 | - - Other: | ||||
| - - - Containing by weight 0.6% or more of carbon, other than of circular cross-section: | |||||
| 7214.99.11 | - - - - Containing by weight less than 1.15% of manganese | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.99.19 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7214.99.91 | - - - - Containing by weight less than 0.38% of carbon, not more than 0.05% of phosphorus and not more than 0.05% of sulphur | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.99.92 | - - - - Containing by weight 0.38% or more of carbon and less than 1.15% of manganese | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.99.93 | - - - - Containing by weight 0.17% or more but less than 0.46% of carbon and 1.2% or more but less than 1.65% of manganese | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7214.99.99 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7215 | Other bars and rods of iron or non-alloy steel | ||||
| 7215.10 | - Of free-cutting steel, not further worked than cold-formed or cold-finished: | ||||
| 7215.10.10 | - - Of circular cross-section | kg | 5% | 0% | 8 / 10 (più aliquote) |
| 7215.10.90 | - - Other | kg | 5% | 0% | 8 / 10 (più aliquote) |
| 7215.50 | - Other, not further worked than cold-formed or cold-finished: | ||||
| 7215.50.10 | - - Containing by weight 0.6% or more of carbon, other than of circular cross-section | kg | 5% | 0% | 8 / 10 (più aliquote) |
| - - Other: | |||||
| 7215.50.91 | - - - Of a kind used for concrete reinforcement (rebars) | kg | 22,5% | 15% | 8 / 10 (più aliquote) |
| 7215.50.99 | - - - Other | kg | 5% | 0% | 8 / 10 (più aliquote) |
| 7215.90 | - Other: | ||||
| 7215.90.10 | - - Of a kind used for concrete reinforcement (rebars) | kg | 22,5% | 15% | 8 / 10 (più aliquote) |
| - - Other: | |||||
| 7215.90.91 | - - - Of circular cross-section | kg | 5% | 0% | 8 / 10 (più aliquote) |
| 7215.90.99 | - - - Other | kg | 5% | 0% | 8 / 10 (più aliquote) |
| 7216 | Angles, shapes and sections of iron or non-alloy steel | ||||
| 7216.10.00 | - U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| - L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of less than 80 mm: | |||||
| 7216.21 | - - L sections: | ||||
| 7216.21.10 | - - - Containing by weight less than 0.6% of carbon | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.21.90 | - - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.22.00 | - - T sections | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| - U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded of a height of 80 mm or more: | |||||
| 7216.31 | - - U sections: | ||||
| 7216.31.10 | - - - Containing by weight 0.6% or more of carbon | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.31.90 | - - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.32 | - - I sections: | ||||
| 7216.32.10 | - - - Of a thickness of 5 mm or less | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.32.90 | - - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.33 | - - H sections: | ||||
| - - - Containing by weight less than 0.6% of carbon: | |||||
| 7216.33.11 | - - - - Thickness of the flange not less than thickness of the web | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7216.33.19 | - - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7216.33.90 | - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7216.40 | - L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of a height of 80 mm or more: | ||||
| 7216.40.10 | - - Containing by weight 0.6% or more of carbon | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.40.90 | - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.50 | - Other angles, shapes and sections, not further worked than hot-rolled, hot-drawn or extruded: | ||||
| - - Of a height of less than 80 mm: | |||||
| 7216.50.11 | - - - Containing by weight 0.6% or more of carbon | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.50.19 | - - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7216.50.91 | - - - Containing by weight 0.6% or more of carbon | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.50.99 | - - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| - Angles, shapes and sections, not further worked than cold-formed or cold-finished: | |||||
| 7216.61.00 | - - Obtained from flat-rolled products | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.69.00 | - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| - Other: | |||||
| 7216.91 | - - Cold-formed or cold-finished from flat-rolled products: | ||||
| 7216.91.10 | - - - Angles, other than slotted angles, containing by weight 0.6% or more of carbon | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.91.90 | - - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7216.99.00 | - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7217 | Wire of iron or non-alloy steel | ||||
| 7217.10 | - Not plated or coated, whether or not polished: | ||||
| 7217.10.10 | - - Containing by weight less than 0.25% of carbon | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| - - Containing by weight 0.25% or more but less than 0.6% of carbon: | |||||
| 7217.10.22 | - - - Reed wire; wire of a kind used for making strands for prestressing concrete; free-cutting steel wire | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7217.10.29 | - - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| - - Containing by weight 0.6% or more of carbon: | |||||
| 7217.10.32 | - - - Spokes wire; reed wire; free-cutting steel wire | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7217.10.33 | - - - Wire of a kind used for making strands for prestressing concrete | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7217.10.39 | - - - Other | kg | 4,5% | 3% | 10 / 8 (più aliquote) |
| 7217.20 | - Plated or coated with zinc: | ||||
| 7217.20.10 | - - Containing by weight less than 0.25% of carbon | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7217.20.20 | - - Containing by weight 0.25% or more of carbon but less than 0.45% of carbon | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - - Containing by weight 0.45% or more of carbon: | |||||
| 7217.20.91 | - - - Steel core wire of a kind used for steel reinforced aluminium conductors (ACSR) | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7217.20.99 | - - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7217.30 | - Plated or coated with other base metals: | ||||
| - - Containing by weight less than 0.25% of carbon: | |||||
| 7217.30.11 | - - - Plated or coated with tin | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7217.30.19 | - - - Other | kg | 22,5% | 15% | 10 / 8 (più aliquote) |
| 7217.30.20 | - - Containing by weight 0.25% or more of carbon but less than 0.6% of carbon | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| - - Containing by weight 0.6% or more of carbon: | |||||
| 7217.30.33 | - - - Brass coated steel wire of a kind used in the manufacture of pneumatic rubber tyres | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7217.30.34 | - - - Other copper alloy coated steel wire of a kind used in the manufacture of pneumatic rubber tyres | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7217.30.35 | - - - Other, plated or coated with tin | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7217.30.39 | - - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7217.90 | - Other: | ||||
| 7217.90.10 | - - Containing by weight less than 0.25% of carbon | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7217.90.90 | - - Other | kg | 7,5% | 5% | 10 / 8 (più aliquote) |
| 7218 | Stainless steel in ingots or other primary forms; semi-finished products of stainless steel | ||||
| 7218.10.00 | - Ingots and other primary forms | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Other: | |||||
| 7218.91.00 | - - Of rectangular (other than square) cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7218.99.00 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7219 | Flat-rolled products of stainless steel, of a width of 600 mm or more | ||||
| - Not further worked than hot-rolled, in coils: | |||||
| 7219.11.00 | - - Of a thickness exceeding 10 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7219.12.00 | - - Of a thickness of 4.75 mm or more but not exceeding 10 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7219.13.00 | - - Of a thickness of 3 mm or more but less than 4.75 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7219.14.00 | - - Of a thickness of less than 3 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Not further worked than hot-rolled, not in coils: | |||||
| 7219.21.00 | - - Of a thickness exceeding 10 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7219.22.00 | - - Of a thickness of 4.75 mm or more but not exceeding 10 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7219.23.00 | - - Of a thickness of 3 mm or more but less than 4.75 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7219.24.00 | - - Of a thickness of less than 3 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Not further worked than cold-rolled (cold-reduced): | |||||
| 7219.31.00 | - - Of a thickness of 4.75 mm or more | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7219.32.00 | - - Of a thickness of 3 mm or more but less than 4.75 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7219.33.00 | - - Of a thickness exceeding 1 mm but less than 3 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7219.34.00 | - - Of a thickness of 0.5 mm or more but not exceeding 1 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7219.35.00 | - - Of a thickness of less than 0.5 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7219.90.00 | - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7220 | Flat-rolled products of stainless steel, of a width of less than 600 mm | ||||
| - Not further worked than hot-rolled: | |||||
| 7220.11 | - - Of a thickness of 4.75 mm or more: | ||||
| 7220.11.10 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7220.11.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7220.12 | - - Of a thickness of less than 4.75 mm: | ||||
| 7220.12.10 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7220.12.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7220.20 | - Not further worked than cold-rolled (cold-reduced): | ||||
| 7220.20.10 | - - Hoop and strip, of a width not exceeding 400 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7220.20.90 | - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7220.90 | - Other: | ||||
| 7220.90.10 | - - Hoop and strip, of a width not exceeding 400 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7220.90.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7221.00.00 | Bars and rods, hot-rolled, in irregularly wound coils, of stainless steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7222 | Other bars and rods of stainless steel; angles, shapes and sections of stainless steel | ||||
| - Bars and rods, not further worked than hot-rolled, hot-drawn or extruded: | |||||
| 7222.11.00 | - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7222.19.00 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7222.20 | - Bars and rods, not further worked than cold-formed or cold-finished: | ||||
| 7222.20.10 | - - Of circular cross-section | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7222.20.90 | - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7222.30 | - Other bars and rods: | ||||
| 7222.30.10 | - - Of circular cross-section | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7222.30.90 | - - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7222.40 | - Angles, shapes and sections: | ||||
| 7222.40.10 | - - Not further worked than hot-rolled, hot-drawn or extruded | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7222.40.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7223 | Wire of stainless steel | ||||
| 7223.00.10 | - Of cross-section exceeding 13 mm | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7223.00.90 | - Other | kg | 15% | 10% | 10 / 8 (più aliquote) |
| 7224 | Other alloy steel in ingots or other primary forms; semi-finished products of other alloy steel | ||||
| 7224.10.00 | - Ingots and other primary forms | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7224.90.00 | - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225 | Flat-rolled products of other alloy steel, of a width of 600 mm or more | ||||
| - Of silicon-electrical steel: | |||||
| 7225.11.00 | - - Grain-oriented | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.19.00 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.30 | - Other, not further worked than hot-rolled, in coils: | ||||
| 7225.30.10 | - - Of high speed steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.30.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.40 | - Other, not further worked than hot-rolled, not in coils: | ||||
| 7225.40.10 | - - Of high speed steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.40.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.50 | - Other, not further worked than cold-rolled (cold-reduced): | ||||
| 7225.50.10 | - - Of high speed steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.50.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Other: | |||||
| 7225.91 | - - Electrolytically plated or coated with zinc: | ||||
| 7225.91.10 | - - - Of high speed steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.91.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.92 | - - Otherwise plated or coated with zinc: | ||||
| 7225.92.10 | - - - Of high speed steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.92.20 | - - - Other, plated or coated with zinc-aluminium-magnesium alloys | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.92.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.99 | - - Other: | ||||
| 7225.99.10 | - - - Of high speed steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7225.99.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226 | Flat-rolled products of other alloy steel, of a width of less than 600 mm | ||||
| - Of silicon-electrical steel: | |||||
| 7226.11 | - - Grain-oriented: | ||||
| 7226.11.10 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.11.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.19 | - - Other: | ||||
| 7226.19.10 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.19.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.20 | - Of high speed steel: | ||||
| 7226.20.10 | - - Hoop and strip, of a width not exceeding 400 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.20.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - Other: | |||||
| 7226.91 | - - Not further worked than hot-rolled: | ||||
| 7226.91.10 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.91.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.92 | - - Not further worked than cold-rolled (cold-reduced): | ||||
| 7226.92.10 | - - - Hoop and strip, of a width not exceeding 400 mm | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.92.90 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.99 | - - Other: | ||||
| - - - Hoop and strip, of a width not exceeding 400 mm: | |||||
| 7226.99.11 | - - - - Plated or coated with zinc | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.99.19 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - - Other: | |||||
| 7226.99.91 | - - - - Plated or coated with zinc | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7226.99.99 | - - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7227 | Bars and rods, hot-rolled, in irregularly wound coils, of other alloy steel | ||||
| 7227.10.00 | - Of high speed steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7227.20.00 | - Of silico-manganese steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7227.90 | - Other: | ||||
| 7227.90.10 | - - Containing by weight 0.5% or more of chromium | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7227.90.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228 | Other bars and rods of other alloy steel; angles, shapes and sections, of other alloy steel; hollow drill bars and rods, of alloy or non-alloy steel | ||||
| 7228.10 | - Bars and rods, of high speed steel: | ||||
| 7228.10.10 | - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.10.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.20 | - Bars and rods, of silico-manganese steel: | ||||
| - - Of circular cross-section: | |||||
| 7228.20.11 | - - - Not further worked than hot-rolled, hot-drawn or extruded | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.20.19 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7228.20.91 | - - - Not further worked than hot-rolled, hot - drawn or extruded | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.20.99 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.30 | - Other bars and rods, not further worked than hot - rolled, hot -drawn or extruded: | ||||
| 7228.30.10 | - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.30.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.40 | - Other bars and rods, not further worked than forged: | ||||
| 7228.40.10 | - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.40.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.50 | - Other bars and rods, not further worked than cold-formed or cold-finished: | ||||
| 7228.50.10 | - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.50.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.60 | - Other bars and rods: | ||||
| 7228.60.10 | - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.60.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.70 | - Angles, shapes and sections: | ||||
| 7228.70.10 | - - Not further worked than hot-rolled, hot-drawn or extruded | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.70.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.80 | - Hollow drill bars and rods: | ||||
| - - Containing by weight 0.6% or more of carbon: | |||||
| 7228.80.11 | - - - Of circular cross-section | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.80.19 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7228.80.90 | - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7229 | Wire of other alloy steel | ||||
| 7229.20.00 | - Of silico-manganese steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7229.90 | - Other: | ||||
| - - Of cross-section not exceeding 5.5 mm: | |||||
| 7229.90.21 | - - - Containing by weight 0.5% or more of chromium | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7229.90.29 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7229.90.30 | - - Other, of high speed steel | kg | 5% | 0% | 10 / 8 (più aliquote) |
| - - Other: | |||||
| 7229.90.91 | - - - Containing by weight 0.5% or more of chromium | kg | 5% | 0% | 10 / 8 (più aliquote) |
| 7229.90.99 | - - - Other | kg | 5% | 0% | 10 / 8 (più aliquote) |